E250 Heatsink Overtemperature Warning散熱器過熱警告。

Description:說明：

The temperature of the heatsink in the drive controller has reached the

maximum allowable temperature. Within a time frame of 30 seconds, the

drive follows the command value input. Consequently, there exists the

possibility to shut down the motor with the control so that it remains true to

the process. (For example close the operation, leave the collision area,

etc.) After 30 seconds, the parameter "Best Possible Deceleration, P-0-

0119" set reaction appears during operation.

驅動器控制器中的散熱器溫度已達到最高允許溫度。在30秒內驅動器遵循命令值輸入。因此，存在使用控制裝置關閉電機的可能性，使其保持正確這一過程。（例如，關閉操作，離開碰撞區域，30秒后，參數“最佳可能減速，P-0-0119“設置反應在操作過程中出現。

Cause:原因：

1. Deficiency of the drive's internal blower.

2. Deficiency of the control cabinet’s climate control.

3. Incorrect control cabinet dimensioning regarding the

head ventilation

1.驅動器內部鼓風機不足。

2.控制柜氣候控制不足。

3.控制柜尺寸不正確頭部通風

Remedy:

For 1. If the blower fails exchange the drive controller.

For 2. Install climitization feature to the cabinet.

For 3. Check the dimensions of the control cabinet.

對于1。如果鼓風機出現故障，更換驅動控制器。

對于2。為機柜安裝氣候調節功能。

對于3。檢查控制柜的尺寸。

F895 4 kHz Signal Error4 kHz信號錯誤。

Description:

The 4kHz signal is synchronized with the software processing for creation

of the resolver signal. This error message is created when

synchronization occurs improperly.

4kHz信號與用于創建的軟件處理同步旋轉變壓器信號的。此錯誤消息是在以下情況下創建的同步發生不正確。

Cause:

1. The synchronization of the resolver controller voltage is invalid

in regards to the software.

2. The error can be produced through an electrical discharge.

1.分解器控制器電壓同步無效關于軟件。

2.該誤差可通過放電產生。

Remedy:補救措施：

For 1. Exchange drive controller and return for testing.

For 2. Power down and then on. If this in not successful; exchange 

drive controller.

對于1。更換驅動器控制器并返回測試。

對于2。關閉電源，然后打開。如果這不成功；交換驅動控制器。